Brackets and mounts
Cabinet Electronics Assembly
- Bounding box
- 393.5 × 143.0 × 206.0 mm
- Engine
- Precision B-rep
- Parameters
- 42
- Published
- October 5, 2026
Download
Free to download and use. See the terms.
The prompt
Create six labeled CAD bodies on the inside of the front door (door inner face at Z=1.5; parts protrude toward +Z). Units: mm. Global coordinates: origin at the front-bottom-left outer corner of the closed cabinet, +X right, +Y up, +Z toward the rear. Model in place. 1) lcd_panel: 10.1 inch capacitive LCD, 235 x 143 x 10 mm, X 22.5-257.5, Y 334.5-477.5, Z 2.5-12.5, with a 222 x 125 mm active-area rectangle centered at (140, 406) on the front face. 2) lcd_controller: placeholder HDMI LCD controller board, 100 x 60 x 12 mm, X 60-160, Y 345-405, Z 12.5-24.5, connectors facing +X. 3) Raspberry_Pi_Camera_Module: name this body exactly Raspberry_Pi_Camera_Module (never OV5647). PCB 25 x 24 x 1.5 mm centered at (295, 406), Z 7-8.5; Ø8 lens barrel Z 2-7 on the axis through the Ø10 door hole; ribbon connector block 6 x 22 x 3 mm on the rear along the right edge. Lens looks toward -Z. 4) raspberry_pi_4b_case_fan: compact Pi 4B case 65 (X 325.5-390.5) x 95 (Y 358.5-453.5) with a 40 x 40 x 7 mm fan on its front face (Z 4.5-11.5, centered at 358, 406, M3 holes on 32 mm pitch) and case body Z 11.5-36.5. Pi orientation: USB/Ethernet end down, USB-C and micro-HDMI edge facing left, microSD end up. Fan direction: exhaust to the front. 5) fan_duct_gasket: foam ring Ø44 outer, Ø38 inner, 3 mm thick, Z 1.5-4.5, centered at (358, 406). 6) fan_airflow_keepout: translucent block 65 x 95 x 15 mm directly behind the case (Z 36.5-51.5). Create three labeled CAD bodies. Units: mm. Global coordinates: origin at the front-bottom-left outer corner of the closed cabinet, +X right, +Y up, +Z toward the rear (back wall inner face at Z=198.5). Model in place. 1) ups_lafvin_3s: PLACEHOLDER envelope 130 x 70 x 45 mm, X 15-145, Y 335-405, Z 153.5-198.5, including four 6 mm standoffs on the back wall. Battery cells face the door (+Z to -Z); an output port on the front face at (X 40, Y 395). 2) ups_service_keepout: translucent block X 15-145, Y 335-405, Z 138.5-153.5. 3) dc_charger_inlet: panel-mount DC jack, Ø14 x 25 mm, axis along X, centered at Y 372, Z 130, spanning X -3 to 22 through the left wall.
Parameters
| Name | Value | Range |
|---|---|---|
| LCD panel length | 235 mm | 150 – 300 |
| LCD panel width | 143 mm | 100 – 200 |
| LCD panel thickness | 10 mm | 4 – 20 |
| Active area length | 222 mm | 150 – 235 |
| Active area width | 125 mm | 100 – 160 |
| Active area recess depth | 1 mm | 0.1 – 3 |
| Controller board length | 100 mm | 50 – 150 |
| Controller board width | 60 mm | 30 – 90 |
| Controller board thickness | 12 mm | 4 – 25 |
| Camera PCB length | 25 mm | 15 – 35 |
| Camera PCB width | 24 mm | 15 – 35 |
| Camera PCB thickness | 1.5 mm | 0.5 – 3 |
| Camera lens barrel diameter | 8 mm | 5 – 12 |
| Camera lens barrel length | 5 mm | 3 – 10 |
| Camera ribbon connector width | 6 mm | 3 – 10 |
| Camera ribbon connector length | 22 mm | 10 – 30 |
| Camera ribbon connector thickness | 3 mm | 1 – 5 |
| Pi case length | 65 mm | 50 – 100 |
| Pi case width | 95 mm | 70 – 110 |
| Pi case body height | 25 mm | 15 – 40 |
| Fan outer size | 40 mm | 25 – 60 |
| Fan thickness | 7 mm | 5 – 15 |
| Fan M3 hole diameter | 3.2 mm | 2.5 – 5 |
| Fan M3 hole pitch | 32 mm | 20 – 45 |
| Gasket outer diameter | 44 mm | 30 – 60 |
| Gasket inner diameter | 38 mm | 25 – 55 |
| Gasket thickness | 3 mm | 1 – 5 |
| Airflow keepout length | 65 mm | 50 – 100 |
| Airflow keepout width | 95 mm | 70 – 110 |
| Airflow keepout height | 15 mm | 10 – 30 |
| UPS envelope length | 130 mm | 90 – 180 |
| UPS envelope width | 70 mm | 50 – 100 |
| UPS envelope height | 45 mm | 30 – 80 |
| UPS standoff diameter | 10 mm | 5 – 20 |
| UPS standoff height | 6 mm | 3 – 12 |
| UPS output port diameter | 12 mm | 6 – 20 |
| UPS output port protrusion depth | 8 mm | 3 – 20 |
| Service keepout length | 130 mm | 90 – 180 |
| Service keepout width | 70 mm | 50 – 100 |
| Service keepout height | 15 mm | 5 – 30 |
| DC jack diameter | 14 mm | 5 – 25 |
| DC jack length | 25 mm | 10 – 40 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Kugoo G2 Pro Rear Swingarm for KuKirin G4
Create a detailed 1:1 CAD drawing of custom rear swingarms for the Kugoo G2 Pro 2020 electric scooter. The swingarms must be designed to fit a KuKirin G4 hub motor instead of the o
Humanoid Robot Exploded Assembly
Design a 3D CAD model of a fully autonomous humanoid biped robot for the Robofest AI HOMO BOT competition. Dimensions Height: 800 mm (80 cm) Maximum weight: 20 kg Lightweight modu