Brackets and mounts
AIRA Desktop Enclosure
- Bounding box
- 100.0 × 110.0 × 45.8 mm
- Engine
- Precision B-rep
- Parameters
- 66
- Published
- September 27, 2026
Download
Free to download and use. See the terms.
The prompt
Design a compact futuristic desktop enclosure for a personal AI assistant named AIRA. The enclosure must be designed around these electronics: 1. ESP32-C3 Super Mini main controller 2. 0.96-inch 128x64 I2C OLED display on the front 3. 2-inch speaker with a front speaker grille 4. INMP441 I2S microphone with a small microphone opening 5. DHT11 temperature and humidity sensor with an exposed airflow opening 6. IR obstacle/proximity sensor on the front 7. MAX98357A I2S amplifier 8. TP4056 USB-C Li-ion charging/protection board 9. MT3608 boost converter 10. One 18650 3.7V 2400mAh battery inside a 1-cell battery holder 11. Small 3-section breadboard for prototyping 12. Internal jumper-wire routing space Create a single compact 3D-printable enclosure with a removable rear cover. Front layout: - 0.96-inch OLED centered in the upper-middle area - futuristic recessed OLED bezel - 2-inch speaker below the OLED - clean geometric speaker grille - IR sensor opening on the front - microphone opening positioned away from the speaker - DHT11 sensor positioned near an external ventilation opening Internal layout: - ESP32-C3 and breadboard mounted securely - dedicated compartments or mounting areas for TP4056, MT3608 and MAX98357A - 18650 battery holder securely mounted - enough clearance for jumper wires and connectors - cable-routing channels - avoid components touching the enclosure walls - leave service access for USB-C charging and programming Design requirements: - compact desktop AI assistant - premium futuristic appearance - smooth chamfered edges - symmetrical geometry - strong but lightweight walls - screw or snap-fit removable rear panel - ventilation slots - USB-C access opening - no sharp edges - designed for FDM 3D printing - avoid unnecessary supports - modular internal mounting - allow approximately 2–3 mm clearance around electronics - do not permanently enclose the DHT11 sensor; it needs airflow Aesthetic: premium futuristic AI device, clean engineering design, subtle cyber-tech appearance, professional rather than toy-like. Add the text "AIRA" on the front exterior. Do not add a lightbulb icon. Do not use the word "IDEA".
Parameters
| Name | Value | Range |
|---|---|---|
| Enclosure Width | 80 mm | 50 – 150 |
| Enclosure Height | 110 mm | 60 – 200 |
| Main Body Depth | 42 mm | 20 – 80 |
| Wall Thickness | 2.5 mm | 1.5 – 5 |
| Outer Corner Radius | 4 mm | 1 – 10 |
| OLED Bezel Width | 30 mm | 20 – 50 |
| OLED Bezel Height | 16 mm | 10 – 30 |
| OLED Bezel Recess Depth | 2 mm | 0.5 – 5 |
| OLED Center Y | 28 mm | 0 – 50 |
| Speaker Grille Diameter | 35 mm | 20 – 60 |
| Speaker Hole Diameter | 2.5 mm | 1 – 6 |
| Speaker Hole Count | 19 mm | 5 – 60 |
| Speaker Center Y | -10 mm | -50 – 40 |
| IR Sensor Hole Diameter | 3.5 mm | 1 – 8 |
| IR Center X | 22 mm | -40 – 40 |
| IR Center Y | -40 mm | -50 – 50 |
| Microphone Hole Diameter | 1.8 mm | 0.5 – 5 |
| Microphone Center X | -22 mm | -40 – 40 |
| Microphone Center Y | -40 mm | -50 – 50 |
| DHT11 Slot Width | 2.5 mm | 1 – 6 |
| DHT11 Slot Height | 8 mm | 3 – 15 |
| DHT11 Slot Count | 4 mm | 1 – 8 |
| DHT11 Vent Center X | 0 mm | -40 – 40 |
| DHT11 Vent Center Y | -50 mm | -50 – 50 |
| AIRA Text Height | 6 mm | 3 – 12 |
| AIRA Text Emboss Depth | 0.8 mm | 0.2 – 2 |
| AIRA Text Center X | 0 mm | -40 – 40 |
| AIRA Text Center Y | 47 mm | -50 – 55 |
| Standoff Height | 6 mm | 3 – 15 |
| Standoff Outer Diameter | 5 mm | 3 – 10 |
| Standoff Screw Hole Dia | 2.5 mm | 1 – 5 |
| Compartment Wall Height | 8 mm | 2 – 15 |
| Compartment Wall Thickness | 2 mm | 1 – 5 |
| TP4056 Area Length | 30 mm | 15 – 50 |
| TP4056 Area Width | 20 mm | 10 – 35 |
| TP4056 Center X | -25 mm | -40 – 40 |
| TP4056 Center Y | 25 mm | -50 – 50 |
| MT3608 Area Length | 25 mm | 10 – 40 |
| MT3608 Area Width | 15 mm | 5 – 30 |
| MT3608 Center X | 25 mm | -40 – 40 |
| MT3608 Center Y | 25 mm | -50 – 50 |
| MAX98357A Area Length | 20 mm | 10 – 40 |
| MAX98357A Area Width | 15 mm | 5 – 30 |
| MAX98357A Center X | 0 mm | -40 – 40 |
| MAX98357A Center Y | 0 mm | -50 – 50 |
| Breadboard Area Length | 35 mm | 20 – 60 |
| Breadboard Area Width | 45 mm | 20 – 70 |
| Breadboard Center X | 0 mm | -40 – 40 |
| Breadboard Center Y | -15 mm | -50 – 50 |
| Battery Holder Length | 70 mm | 40 – 90 |
| Battery Holder Width | 22 mm | 10 – 35 |
| Battery Holder Center X | 0 mm | -40 – 40 |
| Battery Holder Center Y | -35 mm | -50 – 50 |
| Cable Channel Width | 6 mm | 2 – 12 |
| Cable Channel Depth | 3 mm | 1 – 8 |
| Rear Cover Thickness | 3 mm | 1 – 6 |
| Vent Slot Length | 25 mm | 10 – 50 |
| Vent Slot Width | 3 mm | 1 – 8 |
| Vent Slot Count | 5 mm | 2 – 10 |
| Vent Start Y | -30 mm | -50 – 50 |
| USB-C Cutout Width | 10 mm | 6 – 20 |
| USB-C Cutout Height | 4.5 mm | 2 – 10 |
| USB-C Cutout Center Y | 40 mm | -50 – 50 |
| Mounting Tab Width | 8 mm | 3 – 15 |
| Mounting Tab Length | 10 mm | 4 – 20 |
| Rear Screw Hole Dia | 3 mm | 1 – 6 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Kugoo G2 Pro Rear Swingarm for KuKirin G4
Create a detailed 1:1 CAD drawing of custom rear swingarms for the Kugoo G2 Pro 2020 electric scooter. The swingarms must be designed to fit a KuKirin G4 hub motor instead of the o
Humanoid Robot Exploded Assembly
Design a 3D CAD model of a fully autonomous humanoid biped robot for the Robofest AI HOMO BOT competition. Dimensions Height: 800 mm (80 cm) Maximum weight: 20 kg Lightweight modu