Brackets and mounts
2-axis gimbal thrust vector mount (2212 motor)
- Bounding box
- 100 × 85 × 32.0 mm
- Engine
- 3D Printing B-rep
- Parameters
- 36
- Published
- November 22, 2026
Download
Free to download and use. See the terms.
The prompt
Design a 2-axis gimbal thrust vectoring mount for a brushless outrunner motor, for 3D printing in PETG or nylon. All units in millimeters. OVERALL CONCEPT - Base plate fixed to the airframe, holding two MG996R servos side by side (servos stay fixed and do not move with the gimbal). - Outer gimbal ring pivots on the Y axis (yaw) on the base plate. - Inner motor mount ring pivots inside the outer ring on the X axis (pitch). - The two axes intersect at one point on the motor's thrust line. - Each servo drives its axis through a pushrod with ball-link ends (M3 hardware) connecting the servo horn to a control arm on the ring. - Deflection range of +/- 15 degrees on both axes, with no part collisions over the full range. MG996R SERVO POCKETS (x2) - Servo body: 40.7 long x 19.7 wide x 42.9 tall. - Mounting tabs: 54.3 overall length, hole spacing 49.5, 4.5 hole diameter. - Include tab slots/pads and M4 screw holes with 8 mm tall standoffs. - Output shaft is 10 mm from the end of the body. Leave clearance for a standard servo horn (about 38 mm arm length, use a 20 mm hole-to-center distance for the pushrod). - Leave a 10 mm clearance opening for the servo cable exit. MOTOR MOUNT (inner ring) - Motor: 2212-size outrunner, 28 mm bell diameter, with a 16 mm x 19 mm 4-hole M3 mount pattern. - Inner ring has a circular cradle with 4 x M3 holes in that pattern, 3 mm thick, with ventilation cutouts for motor cooling. - Ring outer diameter is 45 mm with 4 mm wall thickness. GIMBAL PIVOTS - Pivot axes use M3 x 20 bolts through the ring walls with flanged bushings or 3 x 8 x 4 mm bearings (include 8 mm bearing seats). - Outer ring inner diameter is 55 mm, with at least 3 mm clearance around the inner ring for tilt. - Control arms are 20 mm long, 5 mm thick, each ending in an M2 hole for the ball link, positioned so a 20 mm servo horn produces about +/- 15 degrees of deflection. STRUCTURE - Minimum wall thickness 3 mm, fillets of 2 mm on all stress corners. - Base plate 100 x 80 x 5 mm with M3 mounting holes in each corner and lightening cutouts. - Print orientation friendly, no supports needed where possible. - Leave a central 40 mm cutout in the base for the thrust and wires to pass.
Parameters
| Name | Value | Range |
|---|---|---|
| Base plate length X | 100 mm | 60 – 200 |
| Base plate width Y | 80 mm | 40 – 160 |
| Base plate thickness | 5 mm | 3 – 10 |
| Servo centre offset from middle, X | 32 mm | 20 – 45 |
| Servo body width | 19.7 mm | 15 – 25 |
| Servo body length | 40.7 mm | 30 – 50 |
| Servo tab hole spacing | 49.5 mm | 40 – 60 |
| Servo tab hole diameter | 4.5 mm | 3 – 6 |
| Standoff height | 8 mm | 4 – 15 |
| Standoff diameter | 8 mm | 5 – 12 |
| Servo cable exit width | 10 mm | 5 – 20 |
| Central thrust cutout diameter | 40 mm | 20 – 60 |
| Corner mounting hole diameter | 3.4 mm | 2.5 – 4 |
| Pivot height above base | 20 mm | 15 – 40 |
| Outer ring outside diameter | 63 mm | 40 – 90 |
| Outer ring inside diameter | 55 mm | 40 – 90 |
| Outer ring height | 12 mm | 6 – 20 |
| Pivot boss diameter | 8 mm | 6 – 12 |
| Control arm length | 20 mm | 10 – 40 |
| Control arm thickness | 5 mm | 3 – 8 |
| M2 ball link hole diameter | 2.2 mm | 1.8 – 3 |
| Servo horn ball height | 30 mm | 20 – 50 |
| Cradle outside diameter | 45 mm | 35 – 60 |
| Cradle wall thickness | 4 mm | 2.5 – 6 |
| Cradle floor thickness | 3 mm | 2 – 6 |
| Cradle height | 12 mm | 8 – 20 |
| Motor bell seat diameter | 28 mm | 20 – 40 |
| Motor mount pattern X | 16 mm | 10 – 30 |
| Motor mount pattern Y | 19 mm | 10 – 30 |
| Pivot bolt diameter | 3 mm | 2.5 – 4 |
| Pivot bolt shank length | 20 mm | 12 – 30 |
| Bolt head diameter | 5.5 mm | 4 – 8 |
| Bolt head height | 3 mm | 2 – 5 |
| Bearing outside diameter | 8 mm | 6 – 10 |
| Bearing bore | 3 mm | 2 – 4 |
| Bearing height | 4 mm | 2 – 6 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Hydraulic Wing and Flaperon Demonstrator
Create a parametric 3D CAD model of a hydraulic aircraft wing and movable flaperon based on the reference sketch. **Wing dimensions:** - 240 mm chord, 120 mm span, 48 mm thickness
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
