Brackets and mounts
0.1 cc/rev Micro Progressive Cavity Pump Assembly
- Bounding box
- 60.0 × 50.0 × 158.0 mm
- Engine
- Precision B-rep
- Parameters
- 35
- Published
- November 22, 2026
Download
Free to download and use. See the terms.
The prompt
Design Prompt — 0.1 cc/Rev Micro Progressive Cavity Pump (PCP): Design a compact, high-precision industrial micro progressive cavity pump (PCP) calibrated to dispense 0.1 cc (0.1 cm³) per shaft revolution with high volumetric repeatability and low pulsation. Core Fluidic & Cavity Geometry: Volumetric Displacement: Exact 0.1 cc/rev theoretical cavity progression, achieved through a tight, micro-machined helical single-start or multi-start rotor rotating inside a matching helical stator to form sealed, progressing fluid chambers from suction to discharge. Rotor & Stator Materials: Precision-ground stainless steel (e.g., 316L or hardened tool steel with low-friction surface treatment) helical rotor paired with a chemical-resistant elastomer (FKM/Viton, EPDM, or HNBR) or low-swell PTFE/engineered polymer stator selected for dimensional stability in micro-cavities. Sealing & Leak Prevention: Zero-dead-volume or minimal-dead-volume transition zones, precision shaft sealing (mechanical seal or multi-lip PTFE/elastomer seal with leak-drain/tell-tale feature), and controlled rotor-stator interference fit to minimize internal slip under backpressure. Drive & Mechanical Architecture: Rotary Drive & Coupling: Compact stepper or closed-loop servo motor input coupled via a low-backlash coupling or eccentric/pin-joint transmission that converts pure rotary shaft turns into smooth planetary/eccentric helical motion without binding. Housing & Porting: CNC-machined anodized aluminum or stainless steel modular housing with compact G1/8" or M6/M8 fluid inlet and outlet ports, clear flow-direction markings, service-friendly stator clamping/retention bolts, and rigid mounting bosses for benchtop or automated gantry/valve integration. Visual & Layout Clarity: Industrial mechanical engineering aesthetic with clean proportions, accessible fastening points, and clear distinction between the drive end, seal/bearing housing, and wet-end pumping chamber. Quick Variations (Depending on How You Use It) For 3D CAD / Sectional Render Prompts: Add "Shown in a clean isometric cutaway / half-section view highlighting the helical rotor, stator cavity, shaft seal, and inlet-to-outlet flow path with crisp studio lighting on a neutral background." For Fluid & Application Tuning: Append your specific fluid properties (viscosity in cP/cps, abrasive vs. non-abrasive fillers, target backpressure in bar/psi, and desired shot/flow rate) so the stator clearance, seal material, and motor torque are locked to the application.
Parameters
| Name | Value | Range |
|---|---|---|
| Motor Body Square | 42 mm | 30 – 60 |
| Motor Body Length | 60 mm | 30 – 90 |
| Motor Shaft Diameter | 5 mm | 3 – 10 |
| Motor Shaft Protrusion | 14 mm | 8 – 30 |
| Mount Housing Square | 50 mm | 36 – 70 |
| Mount Housing Thickness | 20 mm | 10 – 40 |
| Coupling Cavity Bore | 18 mm | 12 – 30 |
| Coupling OD | 16 mm | 10 – 24 |
| Coupling Length | 20 mm | 10 – 40 |
| Coupling Bore | 5 mm | 3 – 10 |
| Eccentric Shaft Diameter | 10 mm | 6 – 16 |
| Eccentric Shaft Length | 24 mm | 15 – 45 |
| Pin Joint Eccentricity | 1 mm | 0.2 – 3 |
| Drive Pin Diameter | 6 mm | 3 – 10 |
| Drive Pin Length | 8 mm | 4 – 20 |
| Seal/Bearing Housing OD | 25 mm | 16 – 40 |
| Seal/Bearing Housing Length | 25 mm | 12 – 45 |
| Shaft Seal OD | 12 mm | 8 – 20 |
| Shaft Seal ID | 10.2 mm | 5 – 16 |
| Shaft Seal Thickness | 8 mm | 3 – 16 |
| Pump Body Width | 60 mm | 40 – 90 |
| Pump Body Depth | 40 mm | 30 – 60 |
| Pump Body Height | 40 mm | 30 – 80 |
| Port Bore (G1/8 approx.) | 8 mm | 4 – 14 |
| Stator OD | 20 mm | 12 – 34 |
| Stator Length | 35 mm | 20 – 70 |
| Rotor Diameter | 6 mm | 3 – 14 |
| Rotor Length | 35 mm | 20 – 70 |
| Rotor Eccentric Offset | 1 mm | 0.2 – 3 |
| Rotor Helix Twist | 180 deg | 0 – 720 |
| Clamp Cap Square | 30 mm | 20 – 50 |
| Clamp Cap Thickness | 10 mm | 5 – 20 |
| Retention Bolt Dia (M3) | 3 mm | 2 – 6 |
| Mounting Foot Size | 15 mm | 8 – 30 |
| Mounting Foot Height | 8 mm | 4 – 20 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Hydraulic Wing and Flaperon Demonstrator
Create a parametric 3D CAD model of a hydraulic aircraft wing and movable flaperon based on the reference sketch. **Wing dimensions:** - 240 mm chord, 120 mm span, 48 mm thickness
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
