Gears and transmission
Water-Powered High-Speed Gearbox (hose, valve, turbine)
- Bounding box
- 102.1 × 150.7 × 93.5 mm
- Engine
- Precision B-rep
- Parameters
- 65
- Published
- November 8, 2026
Download
Free to download and use. See the terms.
The prompt
Water-powered high-speed gearbox: garden-hose (3/4 inch GHT male) inlet, plug valve with 8 mm brass stem and 1 mm brass pins that throttles the flow, nozzle and double-bucket impulse wheel on an 8 mm aluminum shaft in 608 bearings, 5:1 gear stage up to a 3 mm aluminum output rod in 683 bearings; splash-shielded bearings, bottom drain, M3-insert cover
Parameters
| Name | Value | Range |
|---|---|---|
| Gear module | 0.8 mm | 0.6 – 1.5 |
| Pinion teeth (15+ avoids undercut) | 15 | 14 – 22 |
| Speed-up ratio (x:1) | 5 | 3 – 6 |
| Gear face width | 8 mm | 6 – 12 |
| Added centre distance (backlash) | 0.2 mm | 0.1 – 0.5 |
| Bore clearance on the 8 mm shaft | 0.2 mm | 0.1 – 0.4 |
| Pinion bore vs 3 mm axle (negative = tighter) | 0 mm | -0.1 – 0.2 |
| Bearing pocket diametral clearance | 0.2 mm | 0.05 – 0.4 |
| 608 outer diameter | 22 mm | 22 – 22 |
| 608 bore / 8 mm shaft | 8 mm | 8 – 8 |
| 608 width | 7 mm | 7 – 7 |
| 683 outer diameter | 7 mm | 7 – 7 |
| 683 bore / 3 mm axle | 3 mm | 3 – 3 |
| 683 width (each) | 3 mm | 3 – 3 |
| 683 bearings stacked at each end of the axle | 2 | 1 – 2 |
| 608 lip hole diameter | 16 mm | 12 – 19 |
| 683 lip hole diameter | 5 mm | 4 – 6 |
| Pinion stub diameter (bears on inner race) | 5 mm | 4.4 – 5.4 |
| Wet (turbine) chamber height | 28 mm | 24 – 36 |
| Partition thickness (wet/dry divider, holds the bearings) | 8 mm | 8 – 10 |
| Gear to wall gap | 2 mm | 1.5 – 4 |
| Axial end float | 0.4 mm | 0.2 – 0.8 |
| Gear tip to gear-housing wall | 3 mm | 2 – 8 |
| Gear housing wall | 4 mm | 3 – 8 |
| Turbine chamber wall | 6 mm | 5 – 10 |
| Turbine chamber inner radius | 45 mm | 42 – 52 |
| Gear spacer outer diameter | 11 mm | 9 – 12 |
| Drive flat depth on the 8 mm shaft | 0.6 mm | 0.3 – 1.2 |
| Output rod length beyond the cover | 20 mm | 10 – 40 |
| Number of buckets | 18 | 12 – 24 |
| Bucket inner radius | 28 mm | 24 – 32 |
| Bucket outer radius | 36 mm | 32 – 40 |
| Bucket depth (along the jet) | 11 mm | 9 – 14 |
| Bucket pocket radius | 3.3 mm | 2.5 – 4.5 |
| Bucket pocket offset from mid-plane | 3.9 mm | 3 – 6 |
| Bucket back wall thickness | 1.4 mm | 1 – 2.4 |
| Wheel web thickness | 6 mm | 4 – 10 |
| Wheel hub / splash shield diameter | 22 mm | 18 – 26 |
| Nozzle jet diameter | 3.5 mm | 2.5 – 5 |
| Flow bore | 8.4 mm | 7 – 10 |
| Valve body size (square) | 32 mm | 30 – 38 |
| Valve plug diameter | 15.6 mm | 14 – 18 |
| Plug-to-body clearance (diametral) | 0.3 mm | 0.15 – 0.6 |
| Plug cross-hole diameter | 6.6 mm | 5 – 8 |
| Brass stem diameter | 8 mm | 8 – 8 |
| Stem hole oversize | 0.2 mm | 0.1 – 0.5 |
| Brass pin diameter (1 mm rod) | 1 mm | 1 – 1 |
| Stem O-ring inner diameter (optional, 7 x 1.5) | 7 mm | 6 – 8 |
| Stem O-ring cross-section | 1.5 mm | 1 – 2 |
| Valve cap thickness | 5 mm | 4 – 8 |
| Valve handle length | 46 mm | 30 – 70 |
| Hose thread major diameter (3/4 GHT = 26.99, printed slightly under) | 26.6 mm | 26 – 27 |
| Hose thread pitch (11.5 TPI) | 2.21 mm | 2.209 – 2.209 |
| Hose thread depth | 1.35 mm | 1.1 – 1.5 |
| Threaded length | 16 mm | 12 – 20 |
| Hole for M3 heat-set insert | 4.2 mm | 3.8 – 4.6 |
| Insert length (hole depth) | 5.7 mm | 4 – 8 |
| Extra depth below insert | 2.5 mm | 0.5 – 4 |
| M3 clearance hole | 3.5 mm | 3.2 – 3.8 |
| Bolt head counterbore diameter | 6.4 mm | 5.5 – 8 |
| Bolt head counterbore depth | 3.2 mm | 2.5 – 3.5 |
| Gear cover plate thickness | 5 mm | 4.5 – 8 |
| Cover bearing lip thickness | 1.5 mm | 1 – 3 |
| Wall around cover bearing bosses | 2.5 mm | 2 – 4 |
| Outer edge rounding | 1.5 mm | 0.5 – 3 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Meat Grinder Middle Gear
This is the middle gear of the meat grinder: large wheel Ø68 (78 teeth, helical tooth to the right), spur gear Ø20 (8 teeth), hole Ø8, total height 32 mm.