Gears and transmission
Tilting Circular Saw - Exploded Concept
- Bounding box
- 7700 × 500 × 450 mm
- Engine
- 3D Printing B-rep
- Parameters
- 69
- Published
- November 15, 2026
Download
Free to download and use. See the terms.
The prompt
Design a 3D mechanical concept for a tilting woodworking circular saw. Specifications: - Circular saw blade diameter: 300 mm. - Electric motor: 1 horsepower, 2800 RPM. - Belt-and-pulley drive system. - Separate blade shaft supported by two bearing blocks. - The motor, belt drive, bearing blocks, blade shaft, and blade must be mounted together on a rigid moving steel cradle. - The entire assembly must tilt from 0 degrees to 45 degrees while the base remains horizontal. - Use 18 mm Finnish plywood for the stationary base and side supports. - Use steel for the pivot shaft and motor mounting cradle. - Include a positive mechanical angle-locking mechanism. - Include a blade guard and fully enclosed belt and pulleys. - Show the assembly in 3D at 0 and 45 degrees. - Show an exploded view of all components and a parts list. - Clearly identify dimensions that require engineering verification. - Do not assume the shaft diameter, bearing specifications, belt dimensions, or locking hardware dimensions without calculations. - Treat this as a conceptual model only, not a certified design for operation.
Parameters
| Name | Value | Range |
|---|---|---|
| Exploded spacing along X | 600 mm | 300 – 1000 |
| Base plate length | 700 mm | 400 – 900 |
| Base plate width | 500 mm | 300 – 700 |
| Plywood thickness | 18 mm | 12 – 25 |
| Blade clearance slot length | 360 mm | 200 – 500 |
| Blade clearance slot width | 80 mm | 40 – 150 |
| Side plate depth | 350 mm | 250 – 500 |
| Side plate height | 450 mm | 300 – 600 |
| Plywood thickness | 18 mm | 12 – 25 |
| Pivot hole clearance | 0.6 mm | 0.2 – 1.5 |
| Pivot hole height from bed | 320 mm | 150 – 420 |
| Side mounting hole diameter | 8 mm | 4 – 12 |
| Side mounting hole offset in Y | 100 mm | 40 – 150 |
| Side mounting hole height | 40 mm | 15 – 100 |
| Pivot shaft diameter | 26 mm | 15 – 40 |
| Pivot shaft length | 450 mm | 300 – 600 |
| Cradle length in X | 500 mm | 300 – 700 |
| Cradle width in Y | 300 mm | 200 – 500 |
| Cradle height | 250 mm | 150 – 400 |
| Steel plate thickness | 12 mm | 6 – 20 |
| Cradle pivot hole height | 180 mm | 100 – 240 |
| Motor mounting hole diameter | 6.6 mm | 3 – 12 |
| Motor mounting hole X offset | 80 mm | 40 – 150 |
| Motor mounting hole Y offset | 50 mm | 25 – 100 |
| Motor body diameter | 130 mm | 80 – 170 |
| Motor body length | 200 mm | 120 – 300 |
| Motor shaft diameter | 20 mm | 10 – 40 |
| Motor shaft projection | 50 mm | 20 – 100 |
| Motor foot height | 20 mm | 10 – 40 |
| Motor foot width | 30 mm | 15 – 60 |
| Motor foot length | 180 mm | 100 – 280 |
| Motor pulley diameter | 80 mm | 40 – 150 |
| Motor pulley width | 30 mm | 20 – 60 |
| Motor pulley bore | 20.2 mm | 8 – 42 |
| Motor pulley flange thickness | 8 mm | 4 – 15 |
| Blade pulley diameter | 120 mm | 60 – 180 |
| Blade pulley width | 32 mm | 20 – 60 |
| Blade pulley bore | 30.2 mm | 10 – 50 |
| Blade pulley flange thickness | 9 mm | 4 – 15 |
| Belt guard length | 260 mm | 150 – 400 |
| Belt guard width | 180 mm | 100 – 300 |
| Belt guard height | 120 mm | 80 – 200 |
| Belt guard wall thickness | 4 mm | 2 – 8 |
| Belt loop pulley centre gap | 80 mm | 40 – 160 |
| Belt loop outer radius | 22 mm | 10 – 45 |
| Belt loop inner radius | 12 mm | 5 – 30 |
| Belt loop thickness | 6 mm | 3 – 12 |
| Blade shaft diameter | 30 mm | 20 – 50 |
| Blade shaft length | 350 mm | 250 – 500 |
| Bearing block length | 80 mm | 50 – 120 |
| Bearing block width | 60 mm | 40 – 100 |
| Bearing block height | 50 mm | 30 – 90 |
| Saw blade diameter | 300 mm | 200 – 400 |
| Saw blade plate thickness | 3 mm | 1 – 6 |
| Saw blade arbor bore | 30 mm | 10 – 50 |
| Tooth count (count) | 48 mm | 12 – 96 |
| Tooth radial length | 12 mm | 6 – 24 |
| Tooth tangential width | 8 mm | 4 – 16 |
| Tooth overlap into plate | 4 mm | 1 – 8 |
| Blade guard diameter | 350 mm | 250 – 450 |
| Blade guard width | 80 mm | 50 – 150 |
| Blade guard wall thickness | 4 mm | 2 – 10 |
| Sector plate radius | 150 mm | 80 – 220 |
| Sector plate thickness | 8 mm | 4 – 16 |
| Sector angle | 60 deg | 30 – 120 |
| Lock pin diameter | 10 mm | 5 – 20 |
| Lock pin height | 40 mm | 20 – 80 |
| Index hole diameter | 6 mm | 3 – 12 |
| Index hole count (count) | 7 mm | 3 – 15 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Meat Grinder Middle Gear
This is the middle gear of the meat grinder: large wheel Ø68 (78 teeth, helical tooth to the right), spur gear Ø20 (8 teeth), hole Ø8, total height 32 mm.
