Plates and panels
Spray Lever Replacement
- Bounding box
- 57.3 × 26.0 × 7.1 mm
- Engine
- Precision B-rep
- Parameters
- 8
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
Carpet Cleaner Handle - Broken Spray Lever Repair Plan & Customer Job Sheet · Handle from photo - spray trigger lever broken off 1. What is broken The circled part in the photo is the solution spray trigger lever. It sits on the curved handle and, when squeezed, pushes the valve plunger that lets cleaning solution flow through the thin clear tube to the nozzle. The lever is plastic and snaps at the pivot - a common failure. The manufacturer does not sell the lever on its own. The official spare is the complete hose + handle assembly, which is often discontinued or more expensive than the repair. Before you quote, check: (1) Brand + model on the main machine sticker, (2) Does customer still have the broken-off piece? (3) Push the valve plunger by hand - if solution sprays, only the lever is needed. If not, the valve is also faulty. 2. How the new lever works - diagram Bent up PIVOT PIN finger grip 5mm HANDLE BODY NEW LEVER - 3mm aluminium flat bar ~55-60mm long < VALVE PLUNGER When lever is squeezed DOWN, it pushes valve plunger IN = solution sprays Measurements from your photo: lever length +55-60 mm, width +12-14 mm, pivot hole +3 mm. Make the new lever to fit your handle - measure the pivot hole and the distance from pivot to valve plunger before cutting. 3. Repair Option A - Rebuild original lever (if broken piece is available) 1. Clean both faces with methylated spirits. Rough with 80-grit sandpaper. 2. Drill 2-3 mm hole 10-15 mm deep into both sides of the break. 3. Glue a steel pin / nail across the joint with 2-part epoxy (Pratley Steel). The pin carries the load - epoxy alone will snap again. 4. Build up around the joint with Pratley Putty, shape while soft, file smooth when hard. 5. Cure 24 hours. Test 50 squeezes by hand, then test with water before giving back. 4. Repair Option B - Fabricate new lever (if piece is lost) Best for a workshop: cut from 3 mm aluminium flat bar (or stainless). Drill pivot hole, bend the end up slightly for a finger grip, file all edges smooth so it does not cut the hand. Alternative: 3D print in PETG or ABS - not PLA, PLA softens with hot water. Fit, test pivot movement, and check it pushes the valve fully without sticking. 5. Materials list Item Notes 2-part epoxy (Pratley Steel) For pin + joint Pratley Putty Build-up / shaping (Option A) Steel pin / 3mm bolt / nail Backbone across break 3mm aluminium flat bar Option B - new lever 80-grit sandpaper, file, methylated spirits Prep + finishing Small drill + 3mm bit Pivot / pin holes
Parameters
| Name | Value | Range |
|---|---|---|
| Overall lever length | 57 mm | 45 – 70 |
| Lever width | 13 mm | 10 – 18 |
| Material thickness | 3 mm | 1.5 – 5 |
| Finger grip tab length | 12 mm | 5 – 25 |
| Finger grip bend angle | 20 deg | 5 – 45 |
| Pivot hole diameter | 3 mm | 2 – 5 |
| Pivot hole offset from tail | 10 mm | 4 – 20 |
| Edge fillet radius | 0.4 mm | 0.1 – 0.8 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Gabinete Gamer DeX com Suporte Interno para Hub USB-C
Atualize o projeto 3D existente sem mudar o restante do design. - Esconda o hub USB-C em um compartimento interno com tampa removível. - Crie um suporte para o hub entre duas pare
Conveyor Belt Assembly
You can create a CAD model of a conveyor belt with a canvas for furniture weighing 350 kg with sheet metal shoulders and height 850 length 6000 and width canvas 1100
Interdigital Electrode Pattern
### FIG. 2 — Top plan view of the interdigital electrode pattern *Suggested template: USPTO Line Art / Electronic Circuit* ``` FIG. 2: A top plan (bird's-eye) view of an interdigi
3-in-1 Adaptive Jack Head
Create a highly detailed professional mechanical engineering CAD drawing sheet titled: “3-IN-1 ADAPTIVE JACK HEAD – LINE DIAGRAM & DIMENSIONS” Subtitle: “ALL DIMENSIONS ARE IN mm”
FPV Drone Frame (Exploded)
I want a design of a FPV 5 inch carbon frame of a FPV drone racing. Inspied on switchback five 33 frame and similar to BCROW v7. 5mm arms and 2mm top and bottom plate. Make a desig
Adjustable Bracket (Laser Cut)
Give a good laser cutting pattern in 1.6mm thickness sheet
