Gears and transmission
SCARA Vacuum Rover Mechanism - Exploded Parts
- Bounding box
- 3250 × 200 × 650 mm
- Engine
- 3D Printing B-rep
- Parameters
- 14
- Published
- November 22, 2026
Download
Free to download and use. See the terms.
The prompt
Design a compact, mechanically realistic **360° SCARA vacuum-picking mechanism** mounted on a flat 220 × 200 mm rover mounting plate. **Core specifications:** - Z-axis vertical travel: 500 mm. - Two Ø16 mm smooth guide rods. - One centrally positioned T8 lead screw with nut, motor coupling and proper end supports. - Two-link SCARA arm with 150 mm + 150 mm links (300 mm maximum reach from shoulder axis to suction tool centre). - Fully continuous 360° shoulder rotation and independently rotating elbow joint. - Vacuum suction cup at the end of the second link. - Payload: 500 g; use 750 g as the preliminary structural design load. - Vacuum pump mounted low on the rover. **Mechanical design requirements:** 1. Design a rigid Z-axis carriage using four linear bearings (two per guide rod), with adequate bearing separation. 2. Keep the guide rods, lead screw and their supports completely clear of the rotating arm's motion envelope. 3. Mount the SCARA arm above the lift carriage using a properly supported rotary bearing, shoulder shaft and suitable drive arrangement. 4. Include a mechanically supported elbow joint with shaft, bearings and motor mounting. 5. Design rigid, lightweight links with suitable cross-sections; do not rely on weak unsupported 3D-printed beams. 6. Route vacuum hose and cables without twisting, trapping or interfering with movement. Account for a vacuum-rated rotary union for continuous rotation. 7. Include mounting brackets, fasteners, spacers, bearing housings, motor mounts and all essential mechanical components. 8. Ensure access for assembly, maintenance and fastening. 9. Check clearances between every moving and stationary component throughout the full Z travel, 360° shoulder rotation and elbow motion. 10. Evaluate rover tipping risk caused by the 300 mm extended arm. **CAD output:** Generate a complete, clean, dimensioned 3D assembly with realistic component geometry. Show the mounting plate, Z-axis, carriage, rotary assembly, both SCARA links, joints and suction head. Use separate components and logical assemblies. Include a full assembly view and an exploded view if supported. **Engineering priority:** Collision-free movement, structural stiffness, low moving mass, stability, practical manufacturability and easy assembly. Do not sacrifice mechanical feasibility for appearance. If any dimension or arrangement is unsuitable, improve it and clearly identify the change. Do not represent placeholder geometry as a functional bearing, gearbox or rotary union.
Parameters
| Name | Value | Range |
|---|---|---|
| Centre spacing between parts | 280 mm | 100 – 400 |
| Plate X size | 220 mm | 100 – 400 |
| Plate Y size | 200 mm | 100 – 400 |
| Plate thickness | 8 mm | 4 – 20 |
| Guide rod diameter | 16 mm | 8 – 30 |
| Guide rod length | 650 mm | 300 – 900 |
| Vertical spine height | 600 mm | 300 – 900 |
| Rod offset from centreline | 45 mm | 20 – 60 |
| Rod Y offset behind screw | 30 mm | 10 – 40 |
| Link centre-to-centre length | 150 mm | 80 – 250 |
| Shoulder link width | 40 mm | 20 – 80 |
| Shoulder link height | 25 mm | 15 – 60 |
| Forearm width | 35 mm | 20 – 80 |
| Forearm height | 22 mm | 15 – 60 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Meat Grinder Middle Gear
This is the middle gear of the meat grinder: large wheel Ø68 (78 teeth, helical tooth to the right), spur gear Ø20 (8 teeth), hole Ø8, total height 32 mm.
