Gears and transmission
Pan-Tilt Nerf Turret (Panasonic 400W/200W servo)
- Bounding box
- 450.0 × 450.0 × 538.0 mm
- Engine
- Precision B-rep
- Parameters
- 49
- Published
- November 17, 2026
Download
Free to download and use. See the terms.
The prompt
Pan-tilt Nerf gun turret with industrial servomotors: 400 W servo + 30:1 gearbox for pan, 200 W servo + 10:1 gearbox for tilt, Panasonic servos/drivers. Complete mounting and housing for the turret and motors, fabrication-ready detail for handoff to a fabricator.
Parameters
| Name | Value | Range |
|---|---|---|
| Base plate square | 360 mm | 300 – 500 |
| Base plate thickness | 10 mm | 6 – 25 |
| Anchor hole pitch | 330 mm | 250 – 480 |
| Anchor hole dia | 13 mm | 8 – 20 |
| Housing outer width | 300 mm | 260 – 400 |
| Housing height | 280 mm | 240 – 400 |
| Wall thickness | 5 mm | 3 – 10 |
| Top plate thickness | 15 mm | 10 – 30 |
| Rear cable gland hole dia | 32 mm | 16 – 50 |
| Front access opening width | 140 mm | 60 – 250 |
| Front access opening height | 120 mm | 60 – 200 |
| Pan gearbox flange square | 90 mm | 60 – 130 |
| Pan gearbox length | 105 mm | 60 – 180 |
| Pan gearbox pilot dia | 80 mm | 50 – 110 |
| Pan gearbox bolt PCD | 100 mm | 70 – 130 |
| Pan gearbox bolt hole dia | 6.6 mm | 4.5 – 11 |
| Pan servo flange square | 80 mm | 60 – 100 |
| Pan servo length | 112 mm | 80 – 160 |
| Pan output shaft dia | 25 mm | 14 – 40 |
| Slew bearing OD | 220 mm | 150 – 290 |
| Slew bearing ID | 130 mm | 90 – 200 |
| Slew bearing height | 22 mm | 15 – 40 |
| Turntable dia | 260 mm | 200 – 300 |
| Turntable thickness | 15 mm | 10 – 30 |
| Pan hub OD | 75 mm | 50 – 110 |
| Cable pass-through dia | 22 mm | 10 – 24 |
| Yoke inner gap | 150 mm | 120 – 220 |
| Yoke plate thickness | 15 mm | 10 – 25 |
| Yoke plate length | 180 mm | 140 – 200 |
| Tilt axis height above turntable | 130 mm | 100 – 220 |
| Yoke height above tilt axis | 70 mm | 55 – 120 |
| Tilt gearbox flange square | 60 mm | 45 – 90 |
| Tilt gearbox length | 80 mm | 50 – 140 |
| Tilt gearbox pilot dia | 50 mm | 35 – 70 |
| Tilt flange bolt PCD | 70 mm | 55 – 90 |
| Tilt gearbox bolt hole dia | 5.5 mm | 4 – 9 |
| Tilt servo flange square | 60 mm | 40 – 80 |
| Tilt servo length | 100 mm | 70 – 140 |
| Tilt output shaft dia | 19 mm | 12 – 30 |
| Idler stub shaft dia | 25 mm | 12 – 30 |
| Idler bearing bolt hole dia | 9 mm | 5 – 13 |
| Cradle length | 300 mm | 200 – 500 |
| Cradle cheek thickness | 12 mm | 6 – 20 |
| Cradle outer half-width | 58 mm | 40 – 68 |
| Cradle floor thickness | 8 mm | 4 – 15 |
| Trunnion hub dia | 50 mm | 30 – 70 |
| Nerf gun envelope length | 450 mm | 250 – 700 |
| Nerf gun envelope width | 60 mm | 30 – 90 |
| Nerf gun envelope height | 170 mm | 100 – 220 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Meat Grinder Middle Gear
This is the middle gear of the meat grinder: large wheel Ø68 (78 teeth, helical tooth to the right), spur gear Ø20 (8 teeth), hole Ø8, total height 32 mm.
