28.725.522.0
Loading the interactive model…
Interactive 3D model of Flip-Top Dispenser Closure

Gears and transmission

Flip-Top Dispenser Closure

3 views
Bounding box
25.5 × 28.7 × 22.0 mm
Engine
Precision B-rep
Parameters
20
Published
November 15, 2026

Download

Free to download and use. See the terms.

The prompt

Create a compact DETTOL-STYLE FLIP-TOP DISPENSER CLOSURE for a liquid soap/sanitizer container. IMPORTANT: This is NOT a screw cap. DO NOT create any screw threads, helical threads, threaded rings, or twisting mechanism. The closure must use a HINGED FLIP-TOP LID with a SNAP-FIT closure. PART 1 — NECK Create a smooth hollow cylindrical neck: - Outer diameter: 20 mm - Outer radius: 10 mm - Height: 15 mm - Wall thickness: 1.5 mm - Inner diameter: 17 mm - No threads - Smooth cylindrical outer surface - Open at the top - Flat bottom suitable for Boolean Union with my existing soap-case body in Rhino - The neck should be a separate solid from the cap assembly PART 2 — CAP BODY Create a short cylindrical cap body that fits over the outside of the 20 mm neck. - Outer diameter: 25 mm - Height: 9 mm - Wall thickness: 2 mm - Inner diameter approximately 20.6–20.8 mm - Bottom open - Rounded outer edges - Compact proportions similar to a commercial Dettol-style flip-top cap PART 3 — DISPENSING NOZZLE On the top centre of the cap body, create a small raised dispensing nozzle: - Outer diameter: 7 mm - Height: 3.5 mm - Central dispensing hole: 3 mm diameter - The hole must pass through the nozzle and into the inside of the cap - Smooth rounded edges PART 4 — FLIP-TOP LID Create a separate hinged lid on top of the cap body. - Round/oval lid matching the cap body - Approximately 2 mm thick - Slightly rounded/domed top surface - Lid must completely cover the dispensing nozzle when closed - Add a small cylindrical sealing plug underneath the lid that fits into the 3 mm dispensing hole - Plug diameter: approximately 2.5 mm - Plug length: approximately 2 mm PART 5 — HINGE Connect the flip lid to the rear of the cap body using a simple mechanical hinge. - Two hinge ears on the cap body - One central hinge ear on the lid - 2 mm diameter hinge pin - Leave approximately 0.2–0.3 mm clearance around the hinge pin - Lid must be able to rotate at least 90 degrees - Keep the hinge simple and suitable for a 3D-printed prototype PART 6 — SNAP-FIT CLOSURE Add a small snap-fit locking feature at the front of the flip lid. - Small retaining lip on the cap body - Matching small hook/lip on the lid - The lid should press down and CLICK into the closed position - It should be possible to open it by lifting the front edge - Do not use screws, threads, gears, springs, or complicated mechanisms IMPORTANT OUTPUT REQUIREMENTS: - Create the neck, cap body, and flip lid as separate editable solid components. - The lid must remain movable. - The hinge must allow the lid to flip open. - The cap must fit over the 20 mm neck. - No screw threads anywhere. - No helical geometry. - No large bulky cap. - Overall appearance should resemble a small commercial flip-top liquid soap/sanitizer closure. - Keep geometry suitable for importing into Rhino 3D. - Export as STEP (.STEP/.STP).

Parameters

NameValueRange
Neck Outer Diameter20 mm10 – 40
Neck Inner Diameter17 mm5 – 35
Neck Height15 mm5 – 40
Cap Outer Diameter25 mm15 – 50
Cap Inner Diameter20.7 mm10 – 45
Cap Body Height9 mm4 – 20
Cap Deck Thickness1.2 mm0.4 – 3
Nozzle Outer Diameter7 mm3 – 15
Nozzle Height3.5 mm1 – 10
Dispensing Hole Diameter3 mm1 – 8
Lid Diameter25.5 mm15 – 50
Lid Thickness2 mm1 – 6
Sealing Plug Diameter2.5 mm1 – 5.9
Sealing Plug Length2 mm0.5 – 6
Hinge Pin Diameter2 mm1 – 5
Hinge Pin Length10 mm5 – 25
Hinge Pin Clearance0.25 mm0.05 – 1
Hinge Ear Diameter5 mm2 – 12
Cap Hinge Ear Length3 mm1 – 8
Lid Hinge Ear Length2.4 mm0.8 – 6

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

Flip-Top Dispenser Closure - Free CAD Model (STEP, STL) | TextoCAD