Gears and transmission
Flip-Top Dispenser Closure
- Bounding box
- 25.0 × 29.7 × 24.5 mm
- Engine
- Precision B-rep
- Parameters
- 30
- Published
- November 15, 2026
Download
Free to download and use. See the terms.
The prompt
Create a compact DETTOL-STYLE FLIP-TOP DISPENSER CLOSURE for a liquid soap/sanitizer container. IMPORTANT: This is NOT a screw cap. DO NOT create any screw threads, helical threads, threaded rings, or twisting mechanism. The closure must use a HINGED FLIP-TOP LID with a SNAP-FIT closure. PART 1 — NECK Create a smooth hollow cylindrical neck: - Outer diameter: 20 mm - Outer radius: 10 mm - Height: 15 mm - Wall thickness: 1.5 mm - Inner diameter: 17 mm - No threads - Smooth cylindrical outer surface - Open at the top - Flat bottom suitable for Boolean Union with my existing soap-case body in Rhino - The neck should be a separate solid from the cap assembly PART 2 — CAP BODY Create a short cylindrical cap body that fits over the outside of the 20 mm neck. - Outer diameter: 25 mm - Height: 9 mm - Wall thickness: 2 mm - Inner diameter approximately 20.6–20.8 mm - Bottom open - Rounded outer edges - Compact proportions similar to a commercial Dettol-style flip-top cap PART 3 — DISPENSING NOZZLE On the top centre of the cap body, create a small raised dispensing nozzle: - Outer diameter: 7 mm - Height: 3.5 mm - Central dispensing hole: 3 mm diameter - The hole must pass through the nozzle and into the inside of the cap - Smooth rounded edges PART 4 — FLIP-TOP LID Create a separate hinged lid on top of the cap body. - Round/oval lid matching the cap body - Approximately 2 mm thick - Slightly rounded/domed top surface - Lid must completely cover the dispensing nozzle when closed - Add a small cylindrical sealing plug underneath the lid that fits into the 3 mm dispensing hole - Plug diameter: approximately 2.5 mm - Plug length: approximately 2 mm PART 5 — HINGE Connect the flip lid to the rear of the cap body using a simple mechanical hinge. - Two hinge ears on the cap body - One central hinge ear on the lid - 2 mm diameter hinge pin - Leave approximately 0.2–0.3 mm clearance around the hinge pin - Lid must be able to rotate at least 90 degrees - Keep the hinge simple and suitable for a 3D-printed prototype PART 6 — SNAP-FIT CLOSURE Add a small snap-fit locking feature at the front of the flip lid. - Small retaining lip on the cap body - Matching small hook/lip on the lid - The lid should press down and CLICK into the closed position - It should be possible to open it by lifting the front edge - Do not use screws, threads, gears, springs, or complicated mechanisms IMPORTANT OUTPUT REQUIREMENTS: - Create the neck, cap body, and flip lid as separate editable solid components. - The lid must remain movable. - The hinge must allow the lid to flip open. - The cap must fit over the 20 mm neck. - No screw threads anywhere. - No helical geometry. - No large bulky cap. - Overall appearance should resemble a small commercial flip-top liquid soap/sanitizer closure. - Keep geometry suitable for importing into Rhino 3D. - Export as STEP (.STEP/.STP).
Parameters
| Name | Value | Range |
|---|---|---|
| Neck OD | 20 mm | 10 – 40 |
| Neck height | 15 mm | 5 – 40 |
| Neck wall thickness | 1.5 mm | 0.8 – 4 |
| Neck overlap into cap | 6 mm | 1 – 15 |
| Cap body OD | 25 mm | 15 – 50 |
| Cap body ID | 20.7 mm | 12 – 40 |
| Cap body height | 9 mm | 5 – 20 |
| Cap top wall thickness | 2 mm | 1 – 5 |
| Nozzle OD | 7 mm | 3 – 15 |
| Nozzle height | 3.5 mm | 1 – 8 |
| Nozzle hole diameter | 3 mm | 1 – 6 |
| Lid OD | 25 mm | 15 – 50 |
| Lid dome height | 6.5 mm | 3 – 15 |
| Lid wall thickness | 2 mm | 1 – 4 |
| Sealing plug diameter | 2.5 mm | 1 – 5 |
| Sealing plug length | 2 mm | 1 – 4 |
| Hinge pin diameter | 2 mm | 0.5 – 2.5 |
| Hinge clearance | 0.25 mm | 0.05 – 0.5 |
| Hinge pin length | 12 mm | 5 – 25 |
| Cap ear spacing | 7 mm | 4 – 15 |
| Cap ear thickness | 2 mm | 0.5 – 4 |
| Lid ear thickness | 3 mm | 0.5 – 5 |
| Hinge ear length | 4 mm | 2 – 8 |
| Hinge ear height | 4 mm | 2 – 8 |
| Snap lip width | 4 mm | 1 – 8 |
| Snap lip height | 1.5 mm | 0.5 – 4 |
| Snap lip depth | 0.8 mm | 0.2 – 3 |
| Snap hook width | 4 mm | 1 – 8 |
| Snap hook depth | 1.5 mm | 0.5 – 3 |
| Hook below lid rim | 2 mm | 0.5 – 5 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Meat Grinder Middle Gear
This is the middle gear of the meat grinder: large wheel Ø68 (78 teeth, helical tooth to the right), spur gear Ø20 (8 teeth), hole Ø8, total height 32 mm.
