Gears and transmission
Electronic Valve Positioner - Exploded
- Bounding box
- 2944 × 100 × 124 mm
- Engine
- 3D Printing B-rep
- Parameters
- 74
- Published
- November 21, 2026
Download
Free to download and use. See the terms.
The prompt
Design a complete 3D CAD assembly of a **Low-Cost Electronic Valve Positioner with Closed-Loop Position Feedback**. Create a realistic industrial prototype consisting of: 1. A compact rectangular aluminium electronic enclosure (140 × 100 × 70 mm, provisional dimensions) with a removable screw-mounted lid. 2. An ESP32 development board, DC motor driver, voltage regulator and terminal blocks arranged inside the enclosure. 3. An externally mounted low-RPM geared DC motor with a rigid metal mounting bracket. 4. A mechanical shaft coupling connecting the motor to a generic industrial needle valve stem. 5. A position feedback mechanism using a rotary encoder or linear position sensor, with a suitable mounting bracket. 6. A generic needle valve with metal body, threaded stem, inlet and outlet ports. 7. Open and closed limit-switch mounting provisions, cable glands and wiring routes. **Assembly arrangement:** Mount the needle valve at the bottom, geared motor above or beside it, coupling between the motor and valve stem, feedback sensor aligned with the valve movement, and electronic enclosure beside the motor. The system should represent proportional 0–100% valve position control. The ESP32 controls the motor using feedback from the position sensor to reach the commanded position. **Important mechanical requirement:** The needle valve stem rotates and moves axially. Design the coupling so it does not restrict this movement or cause mechanical binding. Generate: - Complete assembled 3D model. - Exploded assembly with separate components. - Isometric engineering view. - Cutaway view showing internal electronics. - Separate editable components. - Realistic mounting holes, fasteners, brackets and clearances. Use realistic mechanical proportions and an industrial engineering appearance. Keep all major components separately editable. Mark dimensions as provisional where actual hardware specifications are unavailable. Do not include pneumatic components, compressed-air systems, solenoid-only ON/OFF operation or decorative futuristic features. Prioritise a practical, manufacturable electromechanical prototype.
Parameters
| Name | Value | Range |
|---|---|---|
| Gap between exploded parts | 30 mm | 10 – 80 |
| Enclosure width | 140 mm | 80 – 200 |
| Enclosure depth | 100 mm | 60 – 160 |
| Enclosure height | 70 mm | 40 – 120 |
| Enclosure wall thickness | 3 mm | 2 – 6 |
| Lid thickness | 4 mm | 2 – 8 |
| M4 clearance hole | 4.5 mm | 3 – 6 |
| Lid screw boss diameter | 8 mm | 5 – 12 |
| PCB standoff height | 6 mm | 3 – 15 |
| PCB standoff diameter | 6 mm | 4 – 10 |
| Gasket groove width | 3 mm | 1.5 – 6 |
| Gasket groove depth | 1 mm | 0.5 – 2 |
| M3 clearance hole | 3.4 mm | 2.5 – 5 |
| ESP32 board width | 55 mm | 30 – 80 |
| ESP32 board depth | 28 mm | 20 – 60 |
| ESP32 PCB thickness | 1.6 mm | 1 – 3 |
| ESP32 overall height | 13 mm | 8 – 25 |
| ESP32 mounting hole | 3.2 mm | 2.5 – 5 |
| ESP32 hole inset | 3.5 mm | 2 – 8 |
| Driver PCB width | 85 mm | 50 – 120 |
| Driver PCB depth | 55 mm | 35 – 90 |
| Driver PCB thickness | 1.6 mm | 1 – 3 |
| Tallest component height | 25 mm | 15 – 45 |
| Driver PCB hole | 3.2 mm | 2.5 – 5 |
| Terminal block width | 18 mm | 8 – 30 |
| Terminal block depth | 12 mm | 6 – 25 |
| Terminal block height | 12 mm | 6 – 25 |
| Heatsink width | 25 mm | 10 – 40 |
| Heatsink depth | 18 mm | 8 – 30 |
| Heatsink height | 14 mm | 5 – 30 |
| Gearbox cross-section | 42 mm | 20 – 70 |
| Motor body length | 90 mm | 50 – 150 |
| Motor shaft diameter | 6 mm | 3 – 12 |
| Output shaft length | 15 mm | 5 – 40 |
| Rear shaft length | 8 mm | 0 – 30 |
| Coupling outside diameter | 20 mm | 10 – 40 |
| Coupling length | 35 mm | 15 – 60 |
| Coupling bore | 6 mm | 3 – 12 |
| Coupling clamp screw | 3.4 mm | 2.5 – 5 |
| Valve body width | 80 mm | 40 – 120 |
| Valve body depth | 60 mm | 35 – 100 |
| Valve body height | 60 mm | 30 – 100 |
| Valve port diameter | 22 mm | 12 – 40 |
| Valve stem diameter | 8 mm | 4 – 16 |
| Valve stem length | 35 mm | 10 – 80 |
| Motor bracket width | 90 mm | 40 – 150 |
| Motor bracket depth/height | 70 mm | 30 – 120 |
| Motor bracket thickness | 6 mm | 3 – 12 |
| Motor slot width | 7 mm | 3 – 12 |
| Motor slot length | 18 mm | 8 – 40 |
| Sensor body width | 30 mm | 15 – 60 |
| Sensor body depth | 30 mm | 15 – 60 |
| Sensor body height | 20 mm | 10 – 50 |
| Sensor shaft diameter | 6 mm | 3 – 12 |
| Sensor shaft length | 10 mm | 3 – 30 |
| Sensor bracket width | 55 mm | 25 – 100 |
| Sensor bracket depth | 35 mm | 20 – 80 |
| Sensor bracket thickness | 3 mm | 1.5 – 8 |
| Sensor adjustment slot length | 14 mm | 6 – 35 |
| Limit bracket width | 70 mm | 35 – 120 |
| Limit bracket depth | 25 mm | 15 – 60 |
| Limit bracket thickness | 3 mm | 1.5 – 8 |
| Microswitch width | 20 mm | 10 – 35 |
| Microswitch depth | 10 mm | 6 – 25 |
| Microswitch height | 6 mm | 3 – 15 |
| Harness length | 200 mm | 80 – 260 |
| Cable bundle diameter | 8 mm | 4 – 16 |
| M12 gland diameter | 12 mm | 8 – 18 |
| M16 gland diameter | 16 mm | 10 – 24 |
| Gland body length | 10 mm | 5 – 20 |
| Ferrule diameter | 2 mm | 1 – 4 |
| Connector width | 12 mm | 6 – 25 |
| Connector depth | 8 mm | 4 – 20 |
| Connector height | 10 mm | 4 – 25 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Meat Grinder Middle Gear
This is the middle gear of the meat grinder: large wheel Ø68 (78 teeth, helical tooth to the right), spur gear Ø20 (8 teeth), hole Ø8, total height 32 mm.
