Gears and transmission
EASYSINK Rotary Mesh Drain Assembly
- Bounding box
- 228.4 × 201.4 × 151.3 mm
- Engine
- Precision B-rep
- Parameters
- 60
- Published
- November 22, 2026
Download
Free to download and use. See the terms.
The prompt
Create an editable, multi-part 3D mechanical CAD assembly of EASYSINK, matching the THREE ATTACHED REFERENCE DIAGRAMS. Use the top-view diagram for the exact horizontal arrangement, the side-view diagram for component heights, and the chute diagram for the waste-transfer mechanism. Model a horizontal circular rotating perforated mesh disc (90 mm diameter, 2 mm thick) inside a stationary hollow drainage housing (96 mm outer diameter, 25 mm deep). Add a stainless-steel mounting rim (120 mm outer diameter, 100 mm inner diameter, 3 mm thick). Attach a large external toothed gear ring to the rotating mesh assembly. Place a small motor-driven pinion at the LEFT side of the gear ring in TOP VIEW, engaging its teeth. Place a fixed diagonal scraper above the mesh, extending toward a waste-transfer opening at the LOWER-RIGHT edge in TOP VIEW. Connect this opening to a downward-sloping chute and a removable rectangular waste bin outside the housing. Include an IR sensor near the upper sink opening, a reed switch beside the removable bin, and a separate bottom drain outlet leading to the P-trap. The mesh and large gear rotate together. The scraper, housing, chute, and motor remain stationary. Water passes through the mesh and drains downward; food particles are guided by the scraper into the chute and bin. Use separate editable CAD solids, realistic gear teeth, actual mesh perforations, and appropriate mechanical clearances. Keep the motor outside the wet drainage area. IMPORTANT: Match the reference diagrams' component placement and connections. Do not create a deep basket, garbage disposal grinder, spinning scraper, or unrelated mechanism. Do not add a full kitchen sink. Prioritize mechanical layout accuracy over decorative appearance.
Parameters
| Name | Value | Range |
|---|---|---|
| Housing OD | 96 mm | 70 – 140 |
| Housing Wall | 3 mm | 2 – 6 |
| Housing Depth | 25 mm | 15 – 45 |
| Floor Thickness | 3 mm | 2 – 8 |
| Waste Opening Width | 55 mm | 30 – 75 |
| Waste Opening Height | 20 mm | 10 – 22 |
| M4 Boss Dia | 8 mm | 5 – 14 |
| M4 Boss Height | 4 mm | 2 – 10 |
| M4 Bolt Circle | 70 mm | 40 – 90 |
| Rim OD | 120 mm | 90 – 170 |
| Rim Bore | 96 mm | 70 – 130 |
| Rim Thickness | 3 mm | 1.5 – 8 |
| Rim Bolt Circle | 110 mm | 85 – 160 |
| Rim Screw Hole | 4.5 mm | 3 – 8 |
| Mesh Disc Dia | 84 mm | 60 – 130 |
| Mesh Thickness | 2 mm | 0.8 – 5 |
| Perforation Dia | 3 mm | 1 – 6 |
| Perforation Pitch | 5 mm | 3.5 – 12 |
| Mesh Plane Height | 17 mm | 5 – 30 |
| Mesh Hub Dia | 26 mm | 12 – 45 |
| Gear Module | 2 mm | 1 – 4 |
| Ring Teeth | 55 teeth | 30 – 90 |
| Ring Face Width | 8 mm | 4 – 20 |
| Ring Bore | 20 mm | 10 – 40 |
| Drive Hub Dia | 24 mm | 12 – 40 |
| Ring Inner Radius | 48 mm | 30 – 60 |
| Pinion Teeth | 10 teeth | 8 – 20 |
| Pinion Face Width | 8 mm | 4 – 20 |
| Pinion Bore | 5 mm | 3 – 12 |
| Pinion Centre Distance | 65 mm | 40 – 90 |
| Motor Body Width | 30 mm | 18 – 50 |
| Motor Body Length | 42 mm | 20 – 80 |
| Gearbox Height | 12 mm | 6 – 30 |
| Scraper Blade Length | 70 mm | 40 – 95 |
| Scraper Blade Width | 18 mm | 8 – 35 |
| Scraper Thickness | 2 mm | 1 – 6 |
| Scraper Height (Z) | 20 mm | 10 – 32 |
| Scraper Diagonal Angle | 45 deg | 20 – 70 |
| Chute Width | 60 mm | 35 – 90 |
| Chute Depth | 35 mm | 15 – 60 |
| Chute Length | 90 mm | 50 – 150 |
| Chute Wall | 1.5 mm | 1 – 5 |
| Chute Slope | 35 deg | 15 – 60 |
| Bin Width (radial) | 80 mm | 50 – 130 |
| Bin Depth (tangential) | 60 mm | 40 – 110 |
| Bin Height | 70 mm | 40 – 110 |
| Bin Wall | 2 mm | 1 – 5 |
| Bin Rim Flange | 5 mm | 2 – 12 |
| Bin Centre Distance | 120 mm | 80 – 180 |
| Drain Spout OD | 32 mm | 20 – 50 |
| Drain Bore | 26 mm | 14 – 42 |
| Drain Spout Length | 30 mm | 15 – 60 |
| Slip-Joint Collar OD | 40 mm | 26 – 60 |
| Drain Offset (+Y) | 29 mm | 0 – 40 |
| IR Sensor Depth | 12 mm | 6 – 25 |
| IR Sensor Width | 20 mm | 8 – 35 |
| IR Sensor Height | 8 mm | 4 – 18 |
| IR Lens Dia | 5 mm | 2 – 12 |
| Reed Switch Dia | 6 mm | 3 – 12 |
| Reed Switch Length | 25 mm | 12 – 50 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Meat Grinder Middle Gear
This is the middle gear of the meat grinder: large wheel Ø68 (78 teeth, helical tooth to the right), spur gear Ø20 (8 teeth), hole Ø8, total height 32 mm.
