Gears and transmission
Desk Buddy 3D Printable Robot
- Bounding box
- 186 × 98 × 152.0 mm
- Engine
- 3D Printing B-rep
- Parameters
- 40
- Published
- November 16, 2026
Download
Free to download and use. See the terms.
The prompt
Create a complete 3D CAD model of a small, friendly, mobile desk companion robot called Desk Buddy. IMPORTANT: I am a beginner, so design this robot for easy 3D printing and assembly. I want a practical, functional design, not just a decorative robot. GENERAL DESIGN: - Approximately 180 mm tall. - Small, compact, square-shaped body with rounded corners. - Cute, friendly robot appearance. - Smooth surfaces and simple geometry. - Designed primarily for FDM 3D printing. - Use millimetres for all dimensions. MAIN BODY: - Hollow rectangular enclosure. - Removable top cover. - Enough internal space for an Arduino Nano, battery, motor driver and wiring. - Internal mounting points for electronics. - Front-facing opening for a 0.96-inch OLED display. - Mounting position for a VL53L0X distance sensor. MOVEMENT SYSTEM: - Two powered wheels, one on each side. - Two small DC geared motors (approximately 6V, 100 RPM). - Motor mounting brackets inside the chassis. - Four small passive caster wheels for stability. - Space for a TB6612FNG motor driver. - Design the bottom so the robot can move on a flat surface. ARMS: - Two simple movable arms. - Each arm should be operated by an SG90 micro servo. - Include servo mounting brackets. - Design the arms as separate printable components. - Keep the arms lightweight and simple. ELECTRONICS: Create dedicated mounting spaces for: - Arduino Nano. - 0.96-inch OLED display. - VL53L0X distance sensor. - TB6612FNG motor driver. - Two SG90 servos. - Two DC geared motors. - Battery holder. - Main power switch. 3D PRINTING REQUIREMENTS: - Separate every major component into individual printable parts. - Avoid unnecessary supports. - Use approximately 2–3 mm wall thickness. - Include screw holes and mounting points. - Avoid permanently closed sections. - Make the electronics accessible for maintenance. IMPORTANT OUTPUT: I want a complete 3D assembly with all major parts positioned correctly. Keep the body, wheels, arms, motor brackets, OLED holder and covers as separate components. Use approximate dimensions where exact measurements are unknown. Do not invent exact electronic component dimensions; use adjustable mounting spaces. Start with a complete rough design. Prioritize functionality, proportions and assembly over appearance. I will refine the exact measurements later.
Parameters
| Name | Value | Range |
|---|---|---|
| Body width X | 110 mm | 80 – 200 |
| Body depth Y | 90 mm | 70 – 180 |
| Body height Z | 120 mm | 80 – 200 |
| Body wall thickness | 2.5 mm | 2 – 4 |
| Body corner radius | 6 mm | 2 – 12 |
| Body floor clearance | 20 mm | 10 – 60 |
| OLED opening width | 30 mm | 20 – 50 |
| OLED opening height | 15 mm | 10 – 30 |
| Sensor window width | 12 mm | 6 – 30 |
| Sensor window height | 8 mm | 5 – 20 |
| Top cover height | 8 mm | 5 – 15 |
| Cover shell thickness | 2.5 mm | 2 – 4 |
| Ventilation slot count | 5 mm | 0 – 12 |
| Screw tab width | 8 mm | 5 – 15 |
| Drive wheel diameter | 55 mm | 40 – 90 |
| Drive wheel width | 20 mm | 10 – 40 |
| Wheel shaft diameter | 6 mm | 4 – 10 |
| Drive axle height above floor | 27.5 mm | 10 – 60 |
| Motor bracket width | 45 mm | 35 – 70 |
| Motor bracket depth | 30 mm | 20 – 50 |
| Motor bracket height | 25 mm | 15 – 40 |
| Motor bracket screw slot width | 3 mm | 2 – 5 |
| Caster wheel diameter | 10 mm | 6 – 20 |
| Caster stem diameter | 3 mm | 2 – 6 |
| Caster inset from body edge | 15 mm | 5 – 40 |
| Arm length | 70 mm | 40 – 120 |
| Arm width | 18 mm | 10 – 40 |
| Arm thickness | 8 mm | 5 – 15 |
| Arm pivot hole diameter | 3 mm | 2 – 6 |
| Arm pivot height above floor | 115 mm | 80 – 160 |
| Servo bracket width | 30 mm | 20 – 50 |
| Servo bracket depth | 20 mm | 12 – 40 |
| Servo bracket height | 18 mm | 10 – 30 |
| Servo bracket screw hole diameter | 2 mm | 1.6 – 3 |
| OLED holder width | 35 mm | 25 – 60 |
| OLED holder height | 22 mm | 15 – 40 |
| OLED holder thickness | 4 mm | 2 – 8 |
| OLED window width | 26 mm | 20 – 40 |
| OLED window height | 14 mm | 10 – 25 |
| OLED holder height above floor | 95 mm | 60 – 140 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Meat Grinder Middle Gear
This is the middle gear of the meat grinder: large wheel Ø68 (78 teeth, helical tooth to the right), spur gear Ø20 (8 teeth), hole Ø8, total height 32 mm.
