Gears and transmission
ATMO-Style Transforming Robot - Exploded Assembly
- Bounding box
- 4335.0 × 110.0 × 41.0 mm
- Engine
- Precision B-rep
- Parameters
- 41
- Published
- November 20, 2026
Download
Free to download and use. See the terms.
The prompt
Create a detailed, editable 3D CAD assembly of a small transforming aerial-ground robot inspired by the ATMO aerially transforming morphobot research concept. **Overall design** The robot must transform between: 1. Ground mode: four wheels contact the ground and allow the robot to drive. 2. Flight mode: four propellers are positioned to provide vertical lift. **Main chassis** - Rectangular central chassis. - Initial target dimensions: 150 mm long × 110 mm wide × 5 mm thick. - Include mounting holes and brackets for motors, pivots, electronics, and mechanical linkages. - Keep the chassis lightweight and allow room for a battery and controller. **Four wheel-thruster assemblies** - Create four separate corner assemblies. - Each assembly contains one wheel, one brushless motor, one propeller, and a pivoting support arm. - Each assembly must rotate as a complete unit between ground and flight configurations. - Keep the wheel axle and the transformation pivot as separate axes. - Make the wheel, motor, propeller, and support arm separate editable components. - Use adjustable dimensions because the exact purchased motor dimensions are not yet confirmed. **Transformation mechanism** - Use one central geared actuator to transform all four assemblies. - Include a worm screw and sliding carriage. - Connect the carriage to a synchronized closed-loop mechanical linkage. - The linkage must move all four pivoting arms together. - Include pivot pins, bearings, brackets, and mechanical stops. - Allow approximately 90 degrees of transformation between the two configurations. - Do not use a tank track or replace the linkage with a decorative chain. - Model actual mechanical joints and clearances. **Ground drive** - Include two separate belt-and-pulley transmission systems, one for each side of the robot. - Include adjustable pulley sizes and belt tensioning. - Keep the ground-drive mechanism separate from the propeller motors. **CAD requirements** - Create a complete assembly with individual editable parts. - Use named parameters for all important dimensions. - Include assembly constraints and rotational joints. - Show both ground and flight configurations. - Provide an exploded assembly view. - Check for collisions between the wheels, propellers, arms, chassis, and linkages. - Export the assembly as STEP and individual components as STL. **Important engineering requirement:** Do not invent unknown dimensions or pretend the mechanism is validated. Make uncertain dimensions adjustable and identify anything that needs physical measurements. The goal is a mechanically understandable prototype, not just a visual concept.
Parameters
| Name | Value | Range |
|---|---|---|
| Chassis Length | 150 mm | 80 – 300 |
| Chassis Width | 110 mm | 60 – 250 |
| Chassis Thickness | 5 mm | 2 – 12 |
| Mounting Hole Dia | 4 mm | 2 – 8 |
| Lightening Hole Dia | 18 mm | 6 – 40 |
| Electronics Bay Length | 55 mm | 20 – 120 |
| Electronics Bay Width | 35 mm | 15 – 90 |
| Electronics Bay Depth | 3 mm | 1 – 4 |
| Wheel Diameter | 60 mm | 30 – 120 |
| Wheel Width | 20 mm | 8 – 50 |
| Wheel Bore | 6 mm | 2 – 15 |
| Motor Diameter | 28 mm | 12 – 60 |
| Motor Length | 30 mm | 15 – 80 |
| Motor Shaft Dia | 5 mm | 2 – 12 |
| Propeller Diameter | 180 mm | 60 – 350 |
| Prop Blade Thickness | 2 mm | 1 – 8 |
| Prop Hub Bore | 5 mm | 2 – 12 |
| Support Arm Length | 70 mm | 30 – 150 |
| Support Arm Width | 14 mm | 6 – 40 |
| Support Arm Thickness | 6 mm | 2 – 20 |
| Transformation Pivot Hole | 5 mm | 2 – 12 |
| Wheel Axle Hole | 6 mm | 2 – 12 |
| Worm Screw Diameter | 8 mm | 4 – 20 |
| Worm Screw Length | 50 mm | 25 – 120 |
| Worm Bracket Height | 12 mm | 6 – 30 |
| Carriage Length | 30 mm | 15 – 80 |
| Carriage Width | 20 mm | 10 – 60 |
| Carriage Height | 10 mm | 4 – 30 |
| Carriage Stroke | 25 mm | 10 – 60 |
| Carriage Link Pin Hole | 4 mm | 1.5 – 10 |
| Loop Linkage Side Length | 60 mm | 40 – 140 |
| Linkage Bar Width | 8 mm | 3 – 15 |
| Linkage Thickness | 5 mm | 2 – 12 |
| Linkage Pin Hole Dia | 4 mm | 1.5 – 10 |
| Pulley Diameter | 20 mm | 10 – 40 |
| Pulley Thickness | 8 mm | 4 – 20 |
| Belt Radial Thickness | 2 mm | 1 – 5 |
| Belt Width | 6 mm | 2 – 15 |
| Pulley Center Distance | 80 mm | 40 – 160 |
| Tension Slot Length | 25 mm | 10 – 60 |
| Exploded Layout Gap | 200 mm | 20 – 400 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Meat Grinder Middle Gear
This is the middle gear of the meat grinder: large wheel Ø68 (78 teeth, helical tooth to the right), spur gear Ø20 (8 teeth), hole Ø8, total height 32 mm.
