Plates and panels
Apple Watch Charger Stand
- Bounding box
- 80.0 × 83.0 × 81.0 mm
- Engine
- Precision B-rep
- Parameters
- 25
- Published
- August 7, 2026
Download
Free to download and use. See the terms.
The prompt
Create a parametric smartwatch desk stand for an Apple Watch Series 9 puck charger. Build the geometry using sequential extrusions and cuts. 1. BASE: Create a flat circular base plate, diameter 80 mm, thickness 6 mm. Cut a straight rectangular wire channel into the bottom face, width 4.2 mm, depth 4.2 mm, running from the center to the back edge. 2. CHARGING DOCK: At the center of the base, add a circular pocket, diameter 27.8 mm, depth 6.0 mm. Cut a 7 mm pass-through hole through the center of this pocket to feed the cable. 3. CHARACTERS BODY STAND: On the rear half of the base plate, extrude a vertical rectangular block 75 mm tall, 45 mm wide, and 30 mm deep to serve as the character torso stand. - Flare the bottom 20 mm of the block outward by 3 mm to form a coat hem. - Add two layered, horizontal rectangular rings around the upper section of the block to represent a stylized scarf. 4. HAIR SEGMENTS: On the back and sides of the vertical block, add five parallel vertical rectangular panels 40 mm long and 3 mm thick to represent stylized straight hair. Cut a 45-degree chamfer at the bottom tip of each hair panel to make them pointed. 5. SUPPORTING ARMS: Extrude two symmetrical geometric arms extending forward from the sides of the vertical torso block. Curve the arms around the left and right sides of the 27.8 mm charging pocket, terminating as simple cuffs that flank the watch face. Cut a 12 mm wide vertical gap on both sides of the pocket for watch strap clearance. 6. FINISHING: Apply a uniform 1.0 mm fillet to all sharp outer edges.
Parameters
| Name | Value | Range |
|---|---|---|
| Base Diameter | 80 mm | 60 – 100 |
| Base Thickness | 6 mm | 4 – 10 |
| Wire Channel Width | 4.2 mm | 3 – 6 |
| Wire Channel Depth | 4.2 mm | 3 – 6 |
| Pocket Diameter | 27.8 mm | 25 – 32 |
| Pocket Depth | 5.9 mm | 4 – 6 |
| Pass-Through Hole Diameter | 7 mm | 5 – 10 |
| Torso Width | 45 mm | 30 – 60 |
| Torso Depth | 30 mm | 20 – 40 |
| Torso Height | 75 mm | 50 – 100 |
| Torso Y Center | -25 mm | -35 – -15 |
| Flare Outward Offset | 3 mm | 1 – 5 |
| Flare Height | 20 mm | 10 – 30 |
| Scarf Ring Thickness | 2 mm | 1 – 5 |
| Scarf Ring Height | 5 mm | 2 – 10 |
| Lower Ring Z Base | 50 mm | 40 – 60 |
| Upper Ring Z Base | 60 mm | 50 – 70 |
| Number of Hair Panels | 5 | 3 – 7 |
| Hair Panel Width | 8 mm | 4 – 12 |
| Hair Panel Thickness | 3 mm | 1 – 5 |
| Hair Panel Length | 40 mm | 30 – 50 |
| Strap Clearance Gap | 12 mm | 8 – 20 |
| Arm Height | 40 mm | 30 – 50 |
| Arm Thickness | 4 mm | 2 – 6 |
| Fillet Radius | 1 mm | 0.5 – 2 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Spur Gearbox
design gearbox
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con