Loading the interactive model…
Interactive 3D model of 18in Cycle Rim on Standing Rod with Gear Motor and Hanging RingGears and transmission
18in Cycle Rim on Standing Rod with Gear Motor and Hanging Ring
1 views
- Bounding box
- 457.3 × 471.2 × 368.5 mm
- Engine
- Precision B-rep
- Parameters
- 34
- Published
- September 13, 2026
Download
Free to download and use. See the terms.
The prompt
Built 18in Cycle Rim on Standing Rod with Gear Motor (precision). make the end of the rode flate stant like make and at the top of the ring small rode like 3mm 10 rodes connect at on ring for hanging the roducts
Parameters
| Name | Value | Range |
|---|---|---|
| Rim Outer Diameter | 457.2 mm | 200 – 700 |
| Rim Radial Thickness | 12 mm | 6 – 40 |
| Rim Width | 20 mm | 6 – 60 |
| Groove Width | 8 mm | 1 – 40 |
| Groove Depth | 6 mm | 0.5 – 20 |
| Hub Diameter | 40 mm | 15 – 120 |
| Hub Height | 40 mm | 10 – 120 |
| Spoke Count | 12 pcs | 3 – 24 |
| Spoke Diameter | 6 mm | 3 – 20 |
| Standing Rod Diameter | 12 mm | 6 – 40 |
| Lower Rod Length | 300 mm | 100 – 800 |
| Upper Rod Length | 8 mm | 0 – 100 |
| Motor Gap in Rod | 80 mm | 40 – 200 |
| Flat Stand Plate Diameter | 60 mm | 20 – 200 |
| Flat Stand Plate Thickness | 8 mm | 3 – 30 |
| Motor Body Width | 40 mm | 20 – 120 |
| Motor Body Depth | 40 mm | 20 – 120 |
| Motor Can Diameter | 30 mm | 10 – 80 |
| Motor Can Length | 60 mm | 20 – 150 |
| Output Shaft Diameter | 10 mm | 4 – 40 |
| Output Shaft Length | 40 mm | 10 – 150 |
| Gear Module | 2 mm | 0.5 – 6 |
| Gear Teeth | 20 pcs | 8 – 60 |
| Gear Face Width | 10 mm | 3 – 40 |
| Gear Bore | 8 mm | 2 – 30 |
| Hanging Rod Count | 10 pcs | 3 – 24 |
| Hanging Rod Diameter | 3 mm | 1 – 10 |
| Hanging Rod Length | 30 mm | 10 – 120 |
| Hanging Rod Bolt Circle | 28 mm | 10 – 80 |
| Hanging Ring OD | 36 mm | 15 – 120 |
| Hanging Ring ID | 22 mm | 5 – 110 |
| Hanging Ring Thickness | 3 mm | 1 – 12 |
| Hanging Base Flange Diameter | 40 mm | 20 – 150 |
| Hanging Base Flange Thickness | 6 mm | 2 – 20 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
STEPSTLGLB16 PARAMS
Spur Gear (12 Teeth)
Built a gear with 12 teeth
STEPSTLGLB5 PARAMS
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
STEPSTLGLB7 PARAMS