Loading the interactive model…
Interactive 3D model of 18in Cycle Rim on Standing Rod with Gear Motor + 10x 3mm Hanger RodsGears and transmission
18in Cycle Rim on Standing Rod with Gear Motor + 10x 3mm Hanger Rods
1 views
- Bounding box
- 457.3 × 465.2 × 576.0 mm
- Engine
- Precision B-rep
- Parameters
- 34
- Published
- September 13, 2026
Download
Free to download and use. See the terms.
The prompt
Built 18in Cycle Rim on Standing Rod with Gear Motor (precision). make the end of the rode flate stant like make and at the top of the ring small rode like 3mm 10 rodes lengh 10cm fixed in thw top of ring
Parameters
| Name | Value | Range |
|---|---|---|
| Rim Outer Diameter | 457.2 mm | 200 – 800 |
| Rim Radial Thickness | 20 mm | 8 – 40 |
| Rim Width | 25 mm | 10 – 60 |
| Tyre Groove Width | 8 mm | 3 – 20 |
| Tyre Groove Depth | 4 mm | 1 – 10 |
| Hub Diameter | 50 mm | 20 – 120 |
| Hub Height | 40 mm | 20 – 100 |
| Spoke Count | 8 pcs | 3 – 16 |
| Spoke Diameter | 8 mm | 3 – 20 |
| Standing Rod Diameter | 20 mm | 8 – 40 |
| Rod Above Hub | 120 mm | 40 – 300 |
| Rod Below Hub | 400 mm | 200 – 900 |
| Motor Gap Height | 80 mm | 40 – 200 |
| Flat Stand Plate Diameter | 50 mm | 20 – 120 |
| Flat Stand Plate Thickness | 10 mm | 3 – 30 |
| Motor Body Width (X) | 42 mm | 20 – 100 |
| Motor Body Depth (Y) | 42 mm | 20 – 100 |
| Motor Can Diameter | 37 mm | 20 – 80 |
| Motor Can Length | 70 mm | 30 – 150 |
| Output Shaft Diameter | 10 mm | 5 – 30 |
| Output Shaft Length | 60 mm | 20 – 150 |
| Gear Module | 2 mm | 0.5 – 5 |
| Gear Teeth | 20 pcs | 8 – 60 |
| Gear Face Width | 12 mm | 5 – 40 |
| Gear Bore | 8 mm | 3 – 30 |
| Hanger Base Disc Diameter | 30 mm | 10 – 300 |
| Hanger Base Disc Thickness | 6 mm | 2 – 25 |
| Hanger Rod Diameter | 3 mm | 1 – 10 |
| Hanger Rod Count | 10 pcs | 3 – 24 |
| Hanger Rod Length | 100 mm | 20 – 400 |
| Hanger Rod Circle Diameter | 24 mm | 8 – 200 |
| Hanging Ring OD | 36 mm | 10 – 300 |
| Hanging Ring ID | 20 mm | 4 – 280 |
| Hanging Ring Thickness | 5 mm | 2 – 20 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
STEPSTLGLB16 PARAMS
Spur Gear (12 Teeth)
Built a gear with 12 teeth
STEPSTLGLB5 PARAMS
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
STEPSTLGLB7 PARAMS