Gears and transmission
1/10 RC Spiral-Bevel Gearbox Assembly (Exploded)
- Bounding box
- 1229.8 × 66.5 × 40.0 mm
- Engine
- Precision B-rep
- Parameters
- 55
- Published
- November 22, 2026
Download
Free to download and use. See the terms.
The prompt
Create an editable parametric, multi-component gearbox for a 1/10-scale RC off-road vehicle. Units: mm. Mechanical accuracy and packaging matter more than appearance. GEARS: Use the supplied spiral-bevel gear CAD models unchanged; their geometry overrides all estimates. Approximate references: ring gear 26 mm diameter, 26 mm overall height, 7 mm upper shaft, 17 mm hub and raised two-hole flange; pinion 13.5 mm gear diameter, 27.5 mm length, 5 mm shaft and 2.2 mm cross-hole. Do not change tooth geometry, ratio, tooth count, spiral direction or orientation. If supplied CAD cannot be used, make labelled placeholders and state mesh is unverified. ORIENTATION: Automotive-style rear ring-and-pinion layout (Ford 9-inch is visual reference only, not dimensions or hypoid geometry). Ring gear vertical, axis lateral across vehicle. Bevel pinion shaft runs front-to-rear, perpendicular to ring axis, entering from the front and meshing at 90°. Never lay ring gear flat or place pinion above/below it. MOTOR DRIVE: Mount a 2436 brushless motor above the gearbox, retaining standard 280 mounting pattern. Motor shaft parallel to bevel-pinion shaft. Connect them with a SEPARATE external 48P spur pair: 13–17T motor pinion and 37–41T driven gear on the exposed 5 mm pinion shaft. Do not combine the driven spur gear with the spiral-bevel pinion. Motor mount must adjust across 13.23–15.35 mm center distance plus backlash; do not design for only one gear pair. HOUSING: Compact practical housing with bearing supports, gear clearance, assembly access, chassis mounts and adjustable motor mount. Single, split or removable-center construction is acceptable. Do not guess unspecified bearing/shaft sizes; use adjustable placeholders and list assumptions. Keep housing, ring gear, bevel pinion, motor, both 48P gears, motor mount, bearing placeholders, covers and fasteners separate. Assemble in operating positions and check mesh and interference. No substitute spur gears for the bevel set; no extra differential internals. OUTPUT: Editable parametric assembly and separate parts; STEP/STL exports; front, rear, side, top and isometric views; sections of both gear meshes; list missing/assumed dimensions. If exact mesh cannot be established from supplied geometry, identify missing information rather than guessing.
Parameters
| Name | Value | Range |
|---|---|---|
| Housing Length X (lateral) | 55 mm | 40 – 80 |
| Housing Width Y (front-rear) | 45 mm | 35 – 70 |
| Housing Height Z | 40 mm | 30 – 60 |
| Wall Thickness | 4 mm | 2 – 8 |
| Ring Gear Bearing Bore | 12 mm | 8 – 20 |
| Pinion Bearing Bore | 8 mm | 5 – 14 |
| Chassis Mount Hole Dia | 3 mm | 2 – 4 |
| Cover Fastener Hole Dia | 2.2 mm | 1.5 – 4 |
| Cover Plate Thickness | 2 mm | 1 – 4 |
| Ring Gear OD | 26 mm | 18 – 40 |
| Ring Gear Rim Thickness | 5 mm | 2 – 10 |
| Ring Gear Hub Dia | 17 mm | 8 – 30 |
| Ring Gear Hub Length | 19 mm | 8 – 35 |
| Ring Gear Shaft Dia | 7 mm | 3 – 14 |
| Ring Gear Upper Shaft Length | 7 mm | 2 – 20 |
| Raised Flange Dia | 24 mm | 12 – 34 |
| Raised Flange Thickness | 2 mm | 1 – 5 |
| Flange Hole Dia | 2.2 mm | 1 – 4 |
| Flange 2-Hole PCD | 21 mm | 6 – 30 |
| Bevel Pinion Gear Dia | 13.5 mm | 8 – 25 |
| Bevel Pinion Gear Length | 8 mm | 3 – 20 |
| Bevel Pinion Shaft Dia | 5 mm | 2 – 12 |
| Bevel Pinion Shaft Length | 19.5 mm | 8 – 45 |
| Pinion Cross-Hole Dia | 2.2 mm | 1 – 4 |
| Motor Body Dia | 24 mm | 15 – 36 |
| Motor Body Length | 36 mm | 20 – 60 |
| Motor Shaft Dia | 2.5 mm | 1 – 5 |
| Motor Shaft Length | 8 mm | 2 – 20 |
| 280 Mount Hole Spacing | 16 mm | 8 – 25 |
| 280 Mount Hole Dia | 2.6 mm | 1.5 – 4 |
| 48P Module (25.4/48) | 0.53 mm | 0.3 – 1 |
| Motor Pinion Teeth (13-17T) | 15 teeth | 10 – 20 |
| Driven Spur Teeth (37-41T) | 39 teeth | 30 – 45 |
| Spur Face Width | 5 mm | 2 – 12 |
| Motor Pinion Bore | 2.5 mm | 1 – 5 |
| Driven Spur Bore | 5 mm | 2 – 8 |
| Motor Plate Width | 30 mm | 20 – 45 |
| Motor Plate Height | 30 mm | 20 – 45 |
| Motor Plate Thickness | 3 mm | 1.5 – 6 |
| Adjustment Slot Length | 12 mm | 5 – 25 |
| Adjustment Slot Width | 2.8 mm | 2 – 5 |
| Ring Bearing Placeholder OD | 12 mm | 6 – 22 |
| Ring Bearing Placeholder ID | 7.2 mm | 3 – 16 |
| Ring Bearing Placeholder Length | 5 mm | 2 – 12 |
| Pinion Bearing Placeholder OD | 8 mm | 5 – 16 |
| Pinion Bearing Placeholder ID | 5.2 mm | 2 – 12 |
| Pinion Bearing Placeholder Length | 4 mm | 2 – 10 |
| Driven Shaft Sleeve OD | 8 mm | 5 – 16 |
| Driven Shaft Sleeve ID | 5.2 mm | 2 – 12 |
| Driven Shaft Sleeve Length | 10 mm | 3 – 25 |
| Screw Shank Dia | 2.3 mm | 1.5 – 3.2 |
| Screw Length | 6 mm | 3 – 16 |
| Screw Head Dia | 4.5 mm | 2.5 – 8 |
| Screw Head Height | 1.5 mm | 0.5 – 3 |
| Exploded Layout Spacing | 80 mm | 40 – 200 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Meat Grinder Middle Gear
This is the middle gear of the meat grinder: large wheel Ø68 (78 teeth, helical tooth to the right), spur gear Ø20 (8 teeth), hole Ø8, total height 32 mm.
